How to connect a mixer to your laptop for a live stream

Take a separate feed from your mixer into your laptop for a live stream, set levels without clipping, and understand USB interfaces and ASIO.

By Abelitie · November 11, 2026
How to connect a mixer to your laptop for a live stream

The short answer

To connect a mixer to a laptop for a live stream:

  1. Take a separate output from the mixer, such as an aux or matrix send, not the main output.
  2. Run it through a USB audio interface into the laptop.
  3. Choose that interface as your microphone in your streaming software.
  4. Set the level so the loudest moments stay well below the red.

The separate output is the part most people skip, and it makes the biggest difference. Everything else is a matter of plugging things in.

Why not use the main output?

Your main output is mixed for the room. That is a different job from a mix for a stream.

In a live room, the drums and the guitar amp are already loud, so the sound engineer turns them down or leaves them out of the speakers. On your stream, that makes them disappear. The vocals sit far too loud, and the band sounds thin.

The main level also moves through the service for the room's sake. If someone pulls the main fader down for a moment, your stream's level goes down too.

An aux or a matrix output avoids both problems, because it has its own levels.

Aux send. Almost every mixer has these, usually for stage monitors. Set one post-fader, so that it follows the channel faders, then build a stream mix on that aux. On a small mixer, this is the usual choice.

Matrix. Larger desks have these. A matrix mixes the groups or mains into a new output, which is a good way to add some of the instruments back.

Subgroup or record out. Some small mixers have a dedicated output. It is easy, but it usually follows the main mix, with all the same problems.

If you only have the main output to work with, use it. A stream with imperfect balance is still better than none. Just don't plan to stay there.

What goes between the mixer and the laptop

A USB audio interface is the normal answer. It takes a line level signal from the mixer and gives the laptop a clean digital signal. A small two-input interface is inexpensive, and it needs nothing else.

A digital desk with USB. Many modern consoles have a USB port that appears on the laptop as an audio device with many channels. If yours has one, you may not need an interface at all.

A laptop's mic socket. Avoid it if you can. It expects a very small signal, so a mixer's output can overload it, and many have hum and noise. If it is all you have, use a pad or an attenuator cable, and keep the level very low.

Cables. Mixer outputs are often XLR or TRS, and interface inputs usually take both. Balanced cables reject hum on longer runs, so use them. If you hear a steady hum that goes away when you unplug the laptop charger, you have a ground loop. A DI box with a ground lift, or a USB isolator, usually fixes it.

Setting the level

This is where streams are won or lost, and digital audio is unforgiving here.

Clipping happens when a signal goes past the top of the meter. On a digital input, it is not a warm distortion. It is a harsh crackle, and you cannot fix it afterwards.

Use this order:

  1. Start with the mixer's send level low and the interface's gain low.
  2. Play the loudest thing you will have, usually the whole band in the last chorus. Do not set your levels on a spoken voice alone.
  3. Raise the interface gain until the peaks sit around two thirds up the meter, which is about -12 dB on a scale that goes to 0.
  4. Check for a red clip light, on the interface and in your software.
  5. Leave room. Worship grows. A level that looks perfect at the soundcheck can clip at the climax.

A stream that is a little too quiet can be turned up. A clipped one cannot be repaired.

Which microphone do you pick?

Plug in the interface. Windows will see it as a recording device. In Broadcasteer, it appears in the microphone dropdown on the audio bar, and this works on every plan, including FREE. Choose it, and watch the meter on the bar move.

Things worth checking:

  • Pick the interface, not the laptop's built-in mic. It is the most common mistake, and it sounds like someone recording a room from a laptop, which it is.
  • Choose the right input. If your interface has two inputs, a feed on input 2 alone may arrive on one side only.
  • Hear what the stream hears. Monitor Out plays that mix to a pair of headphones at the booth. Use it, because the room's speakers will fool you.

ASIO, in plain words

ASIO is a way for audio software to talk directly to a sound device, bypassing the part of Windows that shares and mixes audio. Audio engineers use it for low delay and for access to many channels at once.

Do you need it? Most small churches do not. You might want it if:

  • Your console or interface offers many channels over USB, and you want to pick exactly which pair goes to the stream.
  • You use Dante, through Dante Virtual Soundcard.
  • Your device has an ASIO driver and no ordinary Windows capture.

In Broadcasteer, ASIO is captured by the Stream Module, so it is on PRO and up. To use it:

  1. Install your device's ASIO driver, and start the Stream Module.
  2. Go to Settings, Audio, Pro Audio Input (ASIO). If the module is off, it tells you to start it.
  3. Choose your device under Device. The same drivers appear with a 🎚 in the microphone dropdown on the audio bar.
  4. Under Channels, choose the L and R input channels, numbered from 1, as your console or Dante labels them.
  5. Use Listen to run the meter and check your levels without recording anything.

For Dante Virtual Soundcard, open its settings and set the Audio Interface to ASIO, then restart it. If none appears, you will see "No ASIO drivers found".

One app at a time. An ASIO device can only be used by one program at a time. If it looks busy, close whatever else has it open, and check for a mixing program running in the background.

Before Sunday

Do a real test. Record ten minutes of a full band rehearsal, including the loudest song, then listen to it on phone speakers and on headphones. People will hear your stream on those, not on your studio monitors.

Check three things: Do the vocals sit clearly above the band? Does the sound stay clean at the loudest moment? Does the picture line up with the sound? Your mixer path will add a little delay compared with your cameras, and that is a separate job to measure and correct.

Keep notes of the settings once they work. Mark your aux level and your interface gain with a small piece of tape, so that next week's volunteer can put it back in thirty seconds.

Asked often.

Can connecting my laptop damage the mixer or change the sound in the room?

Connecting to a separate aux or matrix output will not change what the room hears. Keep the laptop off the main outputs, and turn levels down before you plug in, in case of a loud pop.

Do I need to understand ASIO to get a good stream?

No. A USB interface that shows up as a normal microphone works well for many churches. ASIO matters when you have a console or a Dante setup and want to pick specific channels.

Is a laptop's headphone or mic socket good enough?

Only as a stopgap. A laptop mic socket expects a very small signal, so a mixer can overload it, and noise is common. A cheap USB audio interface is a big step up.

Which Broadcasteer plans can use ASIO?

PRO and up, because ASIO is captured by the Stream Module, which runs on those plans. FREE uses a device the browser can see, such as a USB interface or a webcam mic.

Why did Broadcasteer add a different way of taking audio in?

At a national worship event, the venue's audio interface had no capture face at all, so the normal way of reading it found nothing. That day forced a rebuild of how the product takes in sound.

How many apps can use an ASIO device at once?

Only one at a time, which is how ASIO drivers generally behave. If another program has the driver open, close it first. Broadcasteer's Audio settings list the drivers it can find.

Can I choose which channels of my console I capture?

Yes. Under Pro Audio Input (ASIO), choose the device and then a left and right channel pair, numbered from 1 as your console or Dante labels them. Listen runs the meter without having to record.

Try it on your Sunday.

Free tier, no credit card. A laptop and the phones in the room.

Try it free →